LED prices stabilized, crystal power is expected to increase in the second half of the year
Jingdian held a shareholder meeting today and passed the 2014 annual financial report. In 2014, the consolidated revenue was 27.713 billion yuan (NTD, the same below), the operating gross profit was 5.279 billion yuan, the combined gross profit margin was 19.05%, and the pre-tax surplus was 2.196 billion yuan. The after-tax surplus was 1.81 billion yuan, and the earnings per share was 1.98 yuan. The shareholder would pass a cash dividend of 0.83 yuan per share.
In the second quarter of this year, European and American lighting manufacturers lowered their inventory at low prices, triggering a new wave of LED lighting price hikes, and the weak demand for backlights, which made the LED factory's performance in the second quarter generally not as good as expected. However, after the second quarter of the price competition, Li Bingjie believes that the price of LED lighting should not go down in the short term.
Li Bingjie said that this year's global MOCVD will add 250 machines, but it is estimated that 250 old machines will be eliminated, and the mainland's supplementary posts will be gradually over. It is estimated that LED lighting prices will not go down in the short term, LED lighting needs It will be upgraded. At present, there are about 70 billion lamp holders in the world, but the LED market accounts for less than 5%. According to the annual market demand for lighting of about 12 billion lamps, the penetration of LED lighting bulbs is about 20% this year. Billions, growing more than the 1.1 billion last year, have the opportunity to challenge 30% next year.
Looking forward to the second half of the year, Li Bingjie said that in the second half of the year, Jingdian's single plant has the opportunity to be fully loaded. I hope that the industry will win the first quarter and the second quarter in the third quarter. The operation in the first half of the year is about 45:55. It is estimated that this year will be the same.
Features: 12v Dc geared motor drive precision, small volume, large torque, low noise, durability, low energy consumption, customized power design,easy installation, easy maintenance;Simplify design and save space.
12V Dc Gear Motor, namely gear reduction motor, is based on ordinary Dc Motor, coupled with gear reduction gearbox.
The gear reducer is used to provide low speed and large torque.
At the same time, the gearbox with different deceleration ratio can provide different speed and torque.
Generally different industries, using different power dc motor, generally adopt custom parameter design pattern.
Method of use: the best stable in horizontal plane, installed on the 12v dc gear motor output shaft parts, cannot use a hammer to knock,knock prone to press into the 12v dc gear motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
12v Dc geared motors should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a geared motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
12v Dc geared motors should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
The longevity of 12v Dc geared motor is greatly affected by the load conditions , the mode of operation,the environment of use ,etc.Therefore,it is necessary to check the conditions under which the product will actually be used .The following conditions will have a negative effect on longevity.Please consult with us should any of them apply.â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
12V Dc Gear Motor,Dc Gear Motor 12V,12V Gear Motor,12V Dc Gear Motor 30 RPM
Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com